Tools

Part No. 94546-41 Flywheel Shaft Nut Wrench

m

Fits pinion gear nut which secures pinion gear to gear shaft.

W

Part No. 94555-55A Gear Shaft Nut Socket Wrench

Part No. 94555-55A Gear Shaft Nut Socket Wrench

Part No. 94589-29A Cylinder Base Nut Wrench (9/16")

Part No. 94590-73 Cylinder Head Bolt Socket Handle (3/8" Square Drive)

Cylinder Liner Puller

Float Gage Part No. 94752-77

Used for reaming pistons and upper connecting rod bushings.

Part No. 94800-26 Spiral Expansion Reamer

Used to line ream replacement rocker arm bushings to correct size.

Used to line ream replacement rocker arm bushings to correct size.

Part No. 94804-57 Rocker Arm Bushing Reamer m

Used to size pinion shaft gear case cover bushing.

Part No. 94805-57 Pinion Shaft Bushing Reamer and Pilots

I—

Ujf

Has center adapter

M WdlM

for pulling parts from a small diameter shaft.

I O

7

Part No. 95635-46 All Purpose Claw Puller

Used in combination with claw puller for pulling close fitting gears or bearings.

Part No. 95637-46 Wedge Attachment for Claw Puller

For removing bushings and bearings.

Part No. 95760-69 Bushing and Bearing Puller Tool Set (Includes items 1, 2, 3, and 4.) Items 5 (95768-69), 6 (95769-69), 7 (95770-69) and 8 (95771-69) are optional extras.

Used to hold connecting rod firmly so accurate work can be done when fitting piston pin bushing without disassembling crankcase.

Part No. 95952-33 Connecting Rod Clamping Tool

Four holes fit clutch hub studs. Four bolts fit tapped holes in chain housing.

Part No. 95960-41A Clutch Hub and Chain Housing Puller

A^'" ** "I I

| Used to remove and replace || piston pin bushings without removing connecting rod from [ crankcase.

Part No. 95970-32A Piston Pin Bushing Tool

Used with arbor press to press Timken bearing "onto sprocket shaft.

XT

Part No. 96137-52A Flywheel Support Plate

Part No. 96137-52A Flywheel Support Plate

Used on assembled crankcase to determine if a connecting rod is out of true.

Part No. 96180-80 Piston Squaring Plate

Used to check connecting rod alignment.

Special pliers for removing and replacing retaining rings.

96215-49 Small

96216-49 Large

Special pliers for removing and replacing retaining rings.

96215-49 Small

96216-49 Large

Internal Lock Ring Pliers

'Used to insert pistons withl wrings into cylinders. Tool compresses rings to bore size.

Part No. 96333-51A Piston Inserter Ring Tools

For checking valve seat location. Tool consists of two valves and gage having a step to show limits to which valve seat should be ground.

Part No. 96490-59A Valve Seating Gage Seat

Used to rotate valve when grinding or lapping seat surfaces.

Part No. 96550-36 Valve Lapping Tool

Valve Lapping Tools
Used to compress valve springs while removing or installing valves.

Part No. 96180-76 Special Piston with Pin

Part No. 96600-36 Valve Spring Compressor

Used to true flywheel shaft alignment. Measures and indicates alignment to 0.001."

Part No. 96650-30 Flywheel Truing Stand

Part No. 96650-30 Flywheel Truing Stand

Connecting Rod Alignment Fixture
Special fixture with adjustable platform used with torque wrench part No. 96795-47.

Part No. 96796-47 Valve Spring Tester

Aligns pinion shaft main bearing race as well as lapping to size.

Part No. 96710-40 Crankcase Main Bearing Lap

Bench stand which simplifies

overhaul work.

V >

e

Ï/

Part No. 96815-46 Engine Repair Stand

Part No. 96815-46 Engine Repair Stand

Used to lap connecting rod bearing races when fitting new rollers.

Used to lap connecting rod bearing races when fitting new rollers.

Part No. 96740-36 Connecting Rod Lapping Arbor

Used to install and remove pinion gear.

Part No. 96830-51 Pinion Gear Puller and Collars

Range 0 to 100 ft-lbs (1200

in-lbs). Used to tighten head

cylinder, manifold and gener

ator bolts (etc.) where a def-

mite, uniform tightness is

specified. Also used with

Valve Spring Tester Fixture,

^X Part No. 96796-47.

X

Part No. 96795-47 Torque Wrench

Used to check oil pump pressure under actual operating conditions. Attaches to motorcycle. Graduated 0-60 pounds.

Includes adapter to attach hose fitting to 1/8 NPT thread oil pump outlet.

Part No. 96795-47 Torque Wrench

Part No. 96921-52 Oil Pressure Gauge

3-49

Measures chain case vacuum to detect air leaks

Bearing,

For installing flywheel assem-

bly into crankcase Timken

Part No. 96950-68 Vacuum Gauge, 30 Water

Used for tightening band type metal clamps on oil lines.

For installing flywheel assem-

Measures chain case vacuum to bly into crankcase Timken detect air leaks

Bearing,

Part No. 96950-68 Vacuum Gauge, 30 Water

Used for tightening band type metal clamps on oil lines.

Part No. 97225-55 Sprocket Shaft Bearing Tool

Part No, 97087-65A Hose Clamp Pliers

Part No, 97087-65A Hose Clamp Pliers

Oil Pressure Gauge For Rod

Push Rod Adjustment Gauge, Part No. 94438-79

0 -1

Responses

  • Jaana
    How to lap harley connecting rod bearing races?
    5 years ago

Post a comment